CURLOPT_FOLLOWLOCATION(3)

NAME
CURLOPT_FOLLOWLOCATION - follow HTTP 3xx redirects

SYNOPSIS
#include <curl/curl.h>
CURLcode curl_easy_setopt(CURL *handle, CURLOPT_FOLLOWLOCATION, long mode);

DESCRIPTION
This option tells the library to follow Location: header redirects that an HTTP server sends in a 30x response. The Location: header can specify a relative or an absolute URL to follow. The long parameter mode instructs how libcurl should act on subsequent requests. mode only had a single value (1L) for a long time that enables redirect following. Since 8.13.0, two additional modes are also supported. See below. When following redirects, libcurl issues another request for the new URL and follows subsequent new Location: redirects all the way until no more such headers are returned or the maximum limit is reached. CURLOPT_MAXREDIRS(3) is used to limit the number of redirects libcurl follows. libcurl restricts what protocols it automatically follow redirects to. The accepted target protocols are set with CURLOPT_REDIR_PROTOCOLS_STR(3). By default libcurl allows HTTP, HTTPS, FTP and FTPS on redirects. When following a redirect, the specific 30x response code also dictates which request method libcurl uses in the subsequent request: For 301, 302 and 303 responses libcurl switches method from POST to GET unless CURLOPT_POSTREDIR(3) instructs libcurl otherwise. All other redirect response codes make libcurl use the same method again. For users who think the existing location following is too naive, too simple or just lacks features, it is easy to instead implement your own redirect follow logic with the use of curl_easy_getinfo(3)'s CURLINFO_REDIRECT_URL(3) option instead of using CURLOPT_FOLLOWLOCATION(3). By default, libcurl only sends Authentication: or explicitly set Cookie: headers to the initial host given in the original URL, to avoid leaking username + password to other sites. CURLOPT_UNRESTRICTED_AUTH(3) is provided to change that behavior. Due to the way HTTP works, almost any header can be made to contain data a client may not want to pass on to other servers than the initially intended host and for all other headers than the two mentioned above, there is no protection from this happening when libcurl is told to follow redirects. Pick one of the following modes:

CURLFOLLOW_ALL (1)
    Before 8.13.0 this bit had no name and 1L was just the value to enable this option. This makes a set custom method be used in all HTTP requests, even after redirects.

CURLFOLLOW_OBEYCODE (2)
    When there is a custom request method set with CURLOPT_CUSTOMREQUEST(3), that set method replaces what libcurl would otherwise use. If a 301/302/303 response code is returned to signal a redirect, the method is changed from POST to GET. For 307/308, the custom method remains set and used. Note that only POST (or a custom post) is changed to GET on 301/302, its not change PUT etc - and therefore also not when libcurl issues a custom PUT. A 303 response makes it switch to GET independently of the original method (except for HEAD). To control for which of the 301/302/303 status codes libcurl should not switch back to GET for when doing a custom POST, and instead keep the custom method, use CURLOPT_POSTREDIR(3). If you prefer a custom POST method to be reset to exactly the method POST, use CURLFOLLOW_FIRSTONLY instead.

CURLFOLLOW_FIRSTONLY (3)
    When there is a custom request method set with CURLOPT_CUSTOMREQUEST(3), that set method replaces what libcurl would otherwise use in the first outgoing request only. The second request is then done according to the redirect response code. If you prefer your custom method to remain in use after a 307/308 redirect, use CURLFOLLOW_OBEYCODE instead.

NOTE
Since libcurl changes method or not based on the specific HTTP response code, setting CURLOPT_CUSTOMREQUEST(3) while following redirects may change what libcurl would otherwise do and if not that carefully may even make it misbehave since CURLOPT_CUSTOMREQUEST(3) overrides the method libcurl would otherwise select internally. Setting the CURLFOLLOW_OBEYCODE bit makes libcurl not use the custom set method after redirects for 301, 302 and 303 responses. Unless the CURLOPT_POSTREDIR(3) bits are set for those status codes.

DEFAULT
0, disabled

PROTOCOLS
This functionality affects http only

EXAMPLE
int main(void)
{
  CURL *curl = curl_easy_init();
  if(curl) {
    curl_easy_setopt(curl, CURLOPT_URL, "https://example.com");
    /* example.com is redirected, so we tell libcurl to follow redirection */
    curl_easy_setopt(curl, CURLOPT_FOLLOWLOCATION, 1L);
    curl_easy_perform(curl);
  }
}

AVAILABILITY
Added in curl 7.1

RETURN VALUE
curl_easy_setopt(3) returns a CURLcode indicating success or error. CURLE_OK (0) means everything was OK, non-zero means an error occurred, see libcurl-errors(3).

SEE ALSO
CURLINFO_REDIRECT_COUNT(3), CURLINFO_REDIRECT_URL(3), CURLOPT_POSTREDIR(3), CURLOPT_PROTOCOLS_STR(3), CURLOPT_REDIR_PROTOCOLS_STR(3), CURLOPT_UNRESTRICTED_AUTH(3)